So first time user here and looking to expand my knowledge and to help my customers. We're doing a chip off recovery on a LG F60. Device was a no power unit and had some pretty bad water damage so we're attempting a chip off recovery. I do want to touch base I have large amount of experience with Microsoldering and genera BGA reworking. The issue I am having is when reading the chip it says we have no headers for our MBR and GPT partitions. I did get a backup of all three Roms and the EXTSCD file. The following is our log with Easy Jtag Plus unit.



eMMC_tool Suite ver. 1.6.6.0 (release date: 05.05.2021)
Microsoft Windows 10 (64 bit) build 19042 (10.0.19041.1023)


Looking for EasyJTAG box...
EasyJTAG API ver. 3403
EasyJTAG Box Serial = F0701F0EA1E33ACB
Card Serial = AA8515B1
EasyJTAG Box Firmware = 2.5301


Changelog:


05.05.2021 (ver 1.6.6.0)
Add: New keys for Oppo unpack
Fix: Bugs that have been found through your crash report
05.05.2021 (ver 2.0.1.0)
Add: Vendor LG
Add: Mediatek Preloader Parser
Add: OnePlus Unpacker
Add: Xiaomi Custom EDL Authorization
Add: Xiaomi Remove Mi Account (only Qualcomm)


Setting interface to EasyJtag2/E-Socket
Setting bus width to 8 Bit
Setting frequence to 42 MHz
EMMC Device Information :
EMMC CID: 90014A48344731640486029DA35A51A7
EMMC CSD: D02701320F5903FFFFFFFFE78A4040E3
EMMC Manufacture : SKHYNIX , EMMC NAME: H4G1d , HEX: 483447316400 , S/N: 029DA35A , rev. 0x86
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 5/2014
EMMC ROM 1 (Main User Data) Capacity: 3696 MB (0000E7000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 2048 KB (000000200000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 2048 KB (000000200000) Counter: 0 , Response: Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG]: 0x00 , Boot from: no boot
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x03
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G1d_029DA35A_20210630_214049.extcsd
EMMC Init completed.


Scanning soft partitions
Partition table not found


Get firmware version
Firmware info not found


Setting interface to EasyJtag2/E-Socket
Setting bus width to 8 Bit
Setting frequence to 42 MHz
EMMC Device Information :
EMMC CID: 90014A48344731640486029DA35A51A7
EMMC CSD: D02701320F5903FFFFFFFFE78A4040E3
EMMC Manufacture : SKHYNIX , EMMC NAME: H4G1d , HEX: 483447316400 , S/N: 029DA35A , rev. 0x86
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 5/2014
EMMC ROM 1 (Main User Data) Capacity: 3696 MB (0000E7000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 2048 KB (000000200000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 2048 KB (000000200000) Counter: 0 , Response: Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG]: 0x00 , Boot from: no boot
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x03
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G1d_029DA35A_20210630_214936.extcsd
EMMC Init completed.


Scanning soft partitions
Partition table not found


Get firmware version




Firmware info not found


› See More: Having issues using Easy Jtag Plus box